The tip, trailing edge and leading edge of these fins are sharp and can cause cuts. Take care to avoid these sharp edges with your hands, legs or feet especially during water starting.
The following areas should be checked regularly for any signs of wear and tear on your sail:?
- Any dents, wrinkles, imperfections or heavy scratches?on the monofilm or Dyneema material, particularly around the boom, foot, clew, head and leech of the sail.?
- The downhaul pulley attachment point, the clew eyelets, the mast plug attachment point.?
To give your sail a long life:
1. Always rig your sail on grass if possible.?For rigging instructions, please read the "Rigging and Tuning Guides" that are supplied with every NeilPryde sail. These manuals can also be downloaded?here.
2. Sails are damaged easily when left to flap in the wind,?so take care when the sail is not rigged & under tension (ie. during rigging or de-rigging).
3. Always protect your sail from the sun when not in use.?The harmful effects of the sun's rays cause the monofilm material of any sail to breakdown over time. After windsurfing, always de-rig shortly after sailing or protect with a beach cover.
4. Always de-rig your sail after use.For storage, roll the sail tightly from the head, and use the sail bag provided - this helps to prevent premature wear of the monofilm.
5. If possible, store your sail lying flat on the ground & horizontal.?Do not place heavy objects on top of the sail whilst in storage. If it must be stored in a vertical position, ensure that the luff pocket rests on the ground.
6. Always rinse the sail in fresh waterif storing your sail away for the winter or for an extended period of time.
7. Use warm water and mild detergent?to remove persistent dirt.
The carbon material used in your mast can be seriously damaged by impact with a solid object, point loading or extended exposure to sunlight.?This damage may not always be visible to the naked eye. Never place yourself in a situation where the breakage of your mast would make it impossible to return to the shore unaided & without assistance.?
For more information on the care & maintenance of your NeilPryde mast, please read the manual provided with the product.?
The following areas should be checked regularly for any signs of wear & tear on your mast:?
- The boom attachment area
- The cam contact points
- The ferrule joint
To give your mast a long life:
1. Always protect your mast from impact damage or point loading.?Even if there is no visible damage, the mast may be seriously damaged if it is dropped or knocked.
2. Always de-rig your mast shortly after use.?We recommend always using a padded mast bag for storage and transportation.
3. Carbon masts, like any masts, can be crushed or broken from over-tightening the boom.?The best protection against this is to use only NeilPryde RS:X booms.
4. Use NeilPryde RS:X mast bases.?The NeilPryde Extension is only recommended.
5. When rigging a two-piece mast, ensure that the sections are fully engaged after sliding into the luff sleeve.?The easiest way to check this is by running your hand along the luff sleeve before applying final downhaul tension. Any separation could cause the upper section or the ferrule to fail under load.
6. Mast-bases, mast ferrules, luff sleeves, sail cams, and all other components must be free from sand and grit.?Be sure that all your rig components are clean before you rig up. Warm water and mild detergent may be used to remove persistent dirt.
7. Remember that all masts can be broken by even small waves, surf or shorebreak.?Mast breakage resulting from use in breaking waves cannot normally be attributed to defects in manufacturing or material, and is therefore not normally covered under warranty.
8. Although NeilPryde RS:X carbon masts are treated?UV resistant finish, all masts & windsurfing equipment should be kept out of the sun when not in use.
BOOMS & EXTENSIONS
Your boom and/or extension can be seriously damaged by impact with a solid object, extended exposure to sunlight or corrosion (aluminium booms and/or extensions).?This damage may not always be visible to the naked eye. Never place yourself in a situation where the breakage of your boom or extension would make it impossible to return to the shore unaided & without assistance. For more information on the care & maintenance of your NeilPryde RS:X boom and/or extension, please read the RS:X Rigging & Tuning Guide provided with this product.?
The following areas of your boom should be checked regularly for any signs of wear & tear:?
- Mechanical front end parts: front end lever, clamp & screws
- Inhaul adjustment rope
- Back end adjustment levers
To give your Booms & Extensions a long life:
1. Keep your booms & extensions out of the sun when not in use.
2. All sliding components must be free of sand & grit.?Be sure to rinse out your boom in fresh water to prevent the build-up of dirt. This will also prolong the life of your aluminium booms which can be subject to corrosion over time.
3. Do not leave boom clips open?The best protection against this is to use only when not in use.
4. Do not leave your extension inside your mast?when not in use as it may corrode.
The Powerbase unit, including the universal tendon joint, is subject to extreme loads & forces and should be regularly checked and replaced if it shows any signs of wear and tear.?
The universal tendon joint has a limited approximate "lifetime" of up to 120 hours. Furthermore, always check that the RS:X Powerbase is fully inserted into the mast trackof the board, and the locking mechanism is fully closed, before going out onto the water.and should be automatically replaced after this time. For more information on the use, care and maintenance of your Powerbase, please read the RS:X Rigging & Tuning Guide?
The following components of the Powerbase should be checked regularly for any signs of wear & tear:
The Tendon Joint on all Powerbase units should be free of any cracks or blemishes in the rubber material. The easiest way to confirm this, is to bend the joint 90° through 4 different axes while checking the mid-point of the joint. If any cracks appear, the joint should be replaced immediately.
The two upper & lower drift pins holding the tendon into the tendon holder should be tight. The tightness of these pins can be confirmed with an Allen key.
The bottom pin that inserts into the mast track should be flush with the bottom tendon holder and not have any play.
XT Powerbases & XT Pin?
The U-Pin should be flush with the upper tendon holder and note have any play
UXT Powerbases - U-Pin?
The U-Pin should be flush with the upper tendon holder and not have any play.
RS:X Logo (JPG)
Click to View
RS:X Rigging & Tuning Guide 2011.
RS:X Warning, Limited Warranty & Product Care Information 2011.
X3/X6/X9/RS:X Boom Adjustable Outhaul Instructions 2011
RS:X Spare Parts 2011